Ürünlerimiz-Rockwell Auyomation-Micrologix 1500

Introduction   System Components     Example 1768-L4x Configuration  
A basic MicroLogix 1500 system consists of a base unit that provides 24 or 28 built-in basic I/O, a built-in ac or dc power supply, and a processor module that slides into the base unit. You can supplement the I/O built into the base unit with up to sixteen digital and/or analog input and output 1769 Compact™ I/O modules (depending on current draw and power dissipation). Add an optional memory and/or real-time clock module or an optional Data Access Tool to enhance system capability.

•No chassis required : The base unit and Compact I/O modules of the MicroLogix 1500 system can be either panel- or DIN rail-mounted. There is no chassis or rack for expansion I/O.
•Expandable I/O : You can enhance I/O capacity by adding up to sixteen Compact I/O modules (1769 series). Add I/O modules directly to the base unit, or up to a meter away using the available expansion cables and power supplies. Compact I/O modules can be inserted and removed from the front individually.
•MicroLogix and SLC 500 compatible instruction set : Programs written for other MicroLogix or SLC 500 processors can easily be modified to work on a MicroLogix 1500 controller.
•Compatible with RSLogix 500 Programming Software : This feature-rich, user-friendly, Windows-based programming software enables fast program development and increased reusability of programs.
•Easy Interface to System Resources : Built-in function files provide efficient and logical interface to controller resources such as high-speed counters, analog trim pots, or selectable timed interrupts.
•Wide Range of Communication Options : A built-in RS-232 port supports DF1 full- and half-duplex protocols (master as well as slave), Modbus RTU slave protocol (master available late 2003), Radio modem protocol, and full ASCII read and write communication. You can connect the MicroLogix 1500 controller to DH-485, DeviceNet, or EtherNet/IP networks through optional communication interface modules.
•Ease of Wiring and Installation : Removable finger-safe terminal blocks on base units and Compact I/O modules ease wiring, installation, or replacement while meeting global safety standards.
•On-line Data Monitoring and Adjustment : The optional Data Access Tool (DAT) lets you monitor and adjust user-defined integer and bit data. You can insert or remove the DAT while the controller is running.
•Field-upgradeable flash operating system : You can update the controller firmware by using the ControlFlash tool. Controller enhancements can now be downloaded in the field, protecting your investment.
•High-Speed Input and Output Functions : High-speed embedded inputs and outputs allow cost-effective development of both high-speed applications and simple motion control applications without the need for larger or more dedicated controller systems.
  MicroLogix 1500 system components include:
•Processor (1764 -LRP or -LSP, required) : The MicroLogix 1500 processor is a separate module that slides into the base unit. The processor houses a keyless mode switch and two built-in 3/4-turn analog trim potentiometers with a digital output range from 0 to 250. The processor also provides the interface for optional real-time clock and memory modules, and for the Data Access Tool.

•Base Unit (required) : Each MicroLogix 1500 system requires a base unit. The base unit includes embedded I/O and power supply, and provides space for installation of the processor. Three base units are available, each with a different configuration of built-in I/O:

◦1764-24AWA : Twelve 120V ac inputs and twelve relay outputs, 120V ac power.
◦1764-24BWA : Twelve 24V dc inputs and twelve relay outputs, 120V ac power.
◦1764-28BXB : Sixteen 24V dc inputs and six DC FET plus six relay outputs, 24V dc power.

•Compact I/O Modules (1769 series, optional) : Choose from a variety of digital and analog input and output modules. Up to 16 modules can be connected to the MicroLogix 1500 base unit, depending on current draw and power dissipation. Individual modules install to the right of the base unit, or up to 3 feet away through use of an expansion cable (1769-CRRx,-CLLx, or-CRLx) and power supply (1769-PA2, -PA4, -PB2, or -PB4). An end cap (1769-ECR for a right end or 1769-ECL for a left end), or one end of an expansion cable, is required at each end of each bank of Compact I/O modules.*

•Real-Time Clock and Memory Modules (optional) : Real-time clock and memory modules provide memory backup, a real-time clock, or both. Real-time clock data can be accessed by user programs. The real-time clock can be synchronized with an external time source via a program instruction. Three modules are available:

◦1764-MM1RTC : 8K-word combination memory and real-time-clock.
◦1764-MM2RTC : 16K-word combination memory and real-time-clock.
◦1764-MM1 : 8K-word memory only.
◦1764-MM2 : 16K-word memory only.
◦1764-RTC : Real-time-clock only.

•Data Access Tool (1764-DAT, optional) : The Data Access Tool allows monitoring and adjustment of user-defined integer and bit data. It provides 48 “electronic push buttons,” 48 “electronic digital trim potentiometers,” and two function keys. The Data Access Tool can be inserted into or removed from the controller while the system is running, allowing on-line data adjustments.
* The x in catalog numbers 1769-CRRx and 1769-CRLx stands for the number 1 (a one-foot cable) or 3 (a 3-foot cable).

    The MicroLogix 1500 system is designed for ease of installation and maintenance. The base units and Compact I/O modules include finger-safe terminal blocks, and both can be either DIN-rail or panel mounted. The base unit or any I/O module can be removed and installed individually, or the entire system can be removed or installed as a unit.
Two MicroLogix 1500 processor modules are available. The standard processor (1764-LSP) provides up to 7.65K words of configurable user memory with a maximum user data space size of 4K words. The enhanced processor (1764-LRP) provides up to 14K words of configurable user memory with a maximum user data space size of 4K words.
You can create long-integer data files (32-bit signed integer, ± 2 billion) for use with math and embedded high-speed I/O instructions. You can also create floating point data files, each of which can contain up to 256 IEEE-754 floating point data elements.
The MicroLogix 1500 processes a typical 1K-word user program (including bit, timer, counter, and math instructions) in approximately 1ms, and it includes built-in resources to facilitate application development:•Built-in and Modular I/O : The base unit has 24 or 28 built-in I/O. You can add up to 16 I/O modules to support hundreds of I/O points, depending on your power requirements (new 32-point modules available).

•Selectable Timed Interrupt : The selectable timed interrupt (STI) provides a mechanism to solve time-critical control requirements in, for example, PID or motion applications. The STI is a trigger mechanism that lets the controller interrupt the program on a user-defined basis to gather time-sensitive data or initiate outputs.
•Event Input Interrupts : The MicroLogix 1500 controller supports up to 4 event input interrupts, each of which lets the controller scan a specific program file (subroutine) when an input condition is detected from a sensor. These four input interrupts are assignable to any of the eight high-speed inputs. Eight latching or pulse catch inputs allow very brief signals to be captured and held for input processing.
•High-Speed Counters : The MicroLogix 1500 controller (using the 1764-24BWA or -28BXB base unit) includes two built-in independent high-speed counters operating at up to 20kHz, using 32-bit integers for extended range. The high-speed counter instructions support asynchronous control of outputs.
•Programmable Limit Switch Function : The Programmable Limit Switch function allows you to configure the high-speed counter to operate as a programmable limit switch or rotary cam switch.
•Pulse Train and Pulse Width Modulation Outputs : The MicroLogix 1500 controller (using the 1764-28BXB base unit) includes two outputs each of which can be configured as either a high-speed pulse train output (PTO) operating at up to 20kHz or a high-speed pulse width modulated (PWM) output. Trapezoidal and S Curve profiles on PTO outputs allow user-controlled acceleration and deceleration. Both instructions use 32-bit integers for extended range.
•Trim Potentiometers : Two built-in 3/4-turn analog trim potentiometers with a digital output (range from 0 to 250) allow quick and easy adjustments of timers, counters, set points, and more.
Communication   Typical Configurations     Example 1768-L4x Configuration  
RS-232-C : The built-in RS-232-C port supports DF1 full-duplex, DF1 half-duplex slave, new DH1 half-duplex master, DH-485, Modbus RTU slave and new Modbus RTU master protocols, report-by-exception, and peer-to-peer data exchange. This port can be used for direct connection of programming and operator interface devices (e.g. a personal computer), and supports dial-in remote programming.

ASCII : A full ASCII command set for the RS-232-C port allows read and write with ASCII devices.

Modbus : Through its RS-232-C port, use a MicroLogix 1500 system as a smart RTU slave in an existing SCADA network (Modbus master available late 2003).

DH-485 : You can connect the MicroLogix 1500 controller RS-232-C port to a DH-485 network through an Advanced Interface Converter (catalog number 1761-NET-AIC). The DH-485 network may connect up to 32 devices. The communication port provides for program upload and download.

New DF1 Radio Modem protocol : You can transmit data through DF1 Radio Modem protocol, an efficient way to transmit data. Each read/write transaction requires only one TX from initiator and one TX from the responder, so “key-ups” and power consumption are minimized.

DeviceNet : You can connect the MicroLogix 1500 controller RS-232-C port to a DeviceNet network of up to 64 devices through a DeviceNet Interface (catalog number 1761-NET-DNI). The DeviceNet Interface provides slave I/O, peer-to-peer, COS (change-of-state), and program upload/download capability. The MicroLogix 1500 processor supports backplane messaging, which allows the processor to read or write data to other devices on DeviceNet. Finally, you can also use the 1769-SDN Device Net Scanner for DeviceNet master capabilities including messaging, program upload/download and monitoring.

EtherNet/IP : You can connect the MicroLogix 1500 controller to an EtherNet/IP network through an EtherNet/IP-to-RS-232-C interface (catalog number 1761-NET-ENI). This module supports program monitoring and upload/download, data collection, and controller peer-to-peer communication. It can also send e-mail messages via SMTP and display status and configuration information through a built-in Internet server.

Operator interfaces : Many Allen-Bradley operator interface products can be used with MicroLogix 1200 controllers. The PanelView 300 Micro operator interface is a small, low cost, easy-to-use operator interface that is designed for use with the MicroLogix 1200 controller.

For more information see the MicroLogix 1500 Document Update, publication 1764-DU002A-EN-P.

    These specifications cover the base unit, the processor module, real-time-clock/memory module, and data access tool.
Non-Operating Temperature -40…85 °C (-40…185 °F)
Operating Temperature 0…55 °C (32…131 °F)
Operating Humidity 5…95% (without condensation)
Operating Altitude 2,000 m (6,561 ft) max.
Operating 10…500 Hz, 5g, 0.030 inch maximum peak-to-peak
Relay Operation 2g
Shock (Without Data Access Tool installed)
Operating 30g panel mounted (15g DIN Rail mounted)
Relay Operation 7.5g panel mounted (5g DIN Rail mounted)
Non-Operating 40g panel mounted (30g DIN Rail mounted)
Shock (With Data Access Tool installed)
Operating 20g panel mounted (15g DIN Rail mounted)
Relay Operation 7.5g panel mounted (5g DIN Rail mounted)
Non-Operating 30g panel mounted (20g DIN Rail mounted)
Weight 0.9 kg (2.0 lb)
Agency Certification C-UL certified (under CSA C22.2 No. 142)
UL 508 listed
CE compliant for all applicable directives
Hazardous Environment Class Class I, Division 2, Hazardous Location, Groups A, B, C, D (UL 1604, C-UL under CSA C22.2 No. 213)
Radiated and Conducted Emissions EN50081-2 Class A
Electrical and EMC: The module has passed testing at the following levels:
ESD Immunity (IEC1000-4-2) 4 kV contact, 8 kV air, 4 kV indirect
Radiated immunity (IEC1000-4-3) 10V/m, 80…1000 MHz, 80% amplitude modulation, +900 MHz keyed carrier
Fast Transient Burst (IEC1000-4-4) 2 kV, 5 kHz
Surge Immunity (IEC1000-4-5) 2 kV common mode, 1 kV differential mode
Conducted Immunity (IEC1000-4-6) 10V, 0.15…80 MHz*

* Conducted immunity frequency range may be 150 kHz…30 MHz if the radiated immunity frequency range is 30 MHz…1000 MHz.